I think all is working again now. Please leave a comment on a photo somewhere if something you need is not working still.

Main Menu Home About Browse images Signup Lost password? News Links Help User Login User Name Password View By Hangar View By Aircraft Dumas Kit #1815,DeHavilland DH89 Dragon Rapide View Details View All Switch Aircraft Users Aircraft BillParker David Duckett eagraber jgood pakasit1812 pfinn Skyediamonds1985 SteveM

Browse Images Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference Page (4 in total) :  1  [ 2 ]  3   4  [ < Prev ] [ Next > ] Hangar Aircraft Category Date Preview SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 13-Mar-11 20:06 Views : 852 The LHS carries much of the Model Shipways products so I grabbed this 0.028" Nylon rigging line to use for my pull-pull rudder so as no not use up any of the kit supplied rigging line in case there wasn't enough provided for both uses. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 11-Mar-11 19:42 Views : 914 Small pieces of Sullivan cable tubing guide the rudder pull-pull lines where they exit the fuselage. The plans give no guidance on this exit so I borrowed ideas from the builds of others. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 11-Mar-11 19:40 Views : 919 Thread is temporary till I find something more suitable. Brass rod provieds a means to tighten and rough trim. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 08-Mar-11 13:56 Views : 977 Everything seems to fit together nicely. The directions say that the next step is to cover, but I need to figure out the rudder pull-pull lines first. The directions never address installing the pull-pull lines. Weight as shown here is 8.65 oz. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 08-Mar-11 10:36 Views : 801 This being my second Dumas kit I was prepared for incorrect and incomplete instructions, but I wasn't ready for so many errors in the plans. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 08-Mar-11 10:34 Views : 783 Tailwheel assembly installed. Hangar Aircraft Category Date Preview SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 06-Mar-11 17:32 Views : 885 Moving at the speed of PVA glue meant adding these stringers took quite a while. It is the first time I've added fuselage stringers that didn't rest in a notch so it was slow going marking all the positions then holding them in position till the glue set. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 25-Feb-11 21:59 Views : 1003 It took two weeks for the motor wire I ordered to go to my old address 80 miles away before finding its way to me. Of course that wasn't till I gave up and ordered more wire from somewhere else only to have them both arrive in the mail today. Anyhow, all of the electroncs tested out fine. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 09-Feb-11 21:43 Views : 819 The directions say to stick the motor on with silicone caulk, but I drilled a small hole and used some left over servo mounting screws instead. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 09-Feb-11 21:42 Views : 848 Of course the directions tell you to route the wire through a non-existing hole so you have to cut your own. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 09-Feb-11 21:40 Views : 835 Somehow I managed to get this far in the build without thinking about having to extend the motor wires and making a "Y" cable for them. I also need to figure out which motor rotates which way. SteveM Dumas Kit #1815,DeHavilland DH89 Dragon Rapide Build 05-Feb-11 13:32 Views : 917 The HS-55 servos fit well enough, but I had to do some cutting to allow th servo wires and Dubro E/Z connector to clear. The radio is essential to exercise the full range of motion. Page (4 in total) :  1  [ 2 ]  3   4  [ < Prev ] [ Next > ]