| Build Thread, Page :
<< 4 5 6 7 8 [ 9 ] 10 11 12 13 14 (268 posts, 20 posts per page, 14 pages in total)
|
[ < Prev ] [ Next > ] |
| David Duckett, Image # 14638 | 24 Oct 09 18:31 |
|
| David Duckett, Image # 14637 | 24 Oct 09 18:30 |
The doors are cut from a gift card and are taped to the strut for a look see. The actual doors will be balsa. |
| David Duckett, Image # 14636 | 24 Oct 09 18:28 |
The gear pieces are not together yet and the gear is in only for fitting. |
| David Duckett, Image # 14635 | 24 Oct 09 18:26 |
The wing, stabilizer, and fin have been glued on. Filler still needed between fin and fuselage. |
| David Duckett, Image # 14634 | 23 Oct 09 23:33 |
Ready for assembly |
| David Duckett, Image # 14633 | 23 Oct 09 23:31 |
Covering is finished. |
| David Duckett, Image # 14632 | 23 Oct 09 23:30 |
Cockpit enclosed, painted, and instrument panel decal (from a Guillows kit) added. |
| David Duckett, Image # 14610 | 22 Oct 09 11:38 |
|
| RodN, Comment for image # 14592 | 21 Oct 09 00:47 |
| Beautiful job David as always!! |
| David Duckett, Image # 14592 | 20 Oct 09 21:31 |
|
| David Duckett, Image # 14591 | 20 Oct 09 21:30 |
Fuselage covering is complete except for the area just behind the white plastic nose cone. |
| David Duckett, Image # 14590 | 19 Oct 09 22:18 |
Thanks, Jerry. |
| David Duckett, Image # 14589 | 19 Oct 09 22:18 |
|
| jerry campbell, Comment for image # 14585 | 19 Oct 09 20:59 |
| Magnificent David! |
| David Duckett, Image # 14585 | 18 Oct 09 21:40 |
|
| David Duckett, Image # 14584 | 18 Oct 09 21:38 |
The silkspan didn't adhere to the inner stringers so....I used the tip of my xacto blade and made several small holes along the stringer and then put on a small amount of CA and used my finger to press it into place, an operation best done quickly |
| David Duckett, Image # 14583 | 18 Oct 09 21:35 |
|
| David Duckett, Image # 14582 | 18 Oct 09 21:34 |
A second coat of filler was applied to the wing and fuselage and sanded smooth. Then two coats of nitrate dope was applied and sanded smooth. The bottom was then wet covered and given two coats of dope and the bottom fin pieces were glued in place on either side of the wire. This first side section is 3 1/2" wide. |
| FLYBOYZ, Comment for image # 14553 | 18 Oct 09 19:43 |
| Lovely David!Frost in alabama early morning day break! |
| David Duckett, Image # 14575 | 18 Oct 09 13:27 |
The bottom is ready for covering. Two balsa pieces fit on either side of the tailwheel wire and will be added when covering is finished. |
| Build Thread, Page :
<< 4 5 6 7 8 [ 9 ] 10 11 12 13 14 (268 posts, 20 posts per page, 14 pages in total)
|
[ < Prev ] [ Next > ] |
