| Build Thread, Page :
1 2 3 4 5 6 7 8 9 10 11 >> (423 posts, 20 posts per page, 22 pages in total)
|
[ < Prev ] [ Next > ] |
| John M Oshust, Image # 21549 | 09 Mar 11 16:49 |
It is getting hard to find gas resistant rubber "O" rings for fuel line installs. |
| John M Oshust, Image # 21548 | 09 Mar 11 16:47 |
I hooked the pump to the engine and fuel tank. |
| John M Oshust, Comment for image # 21540 | 08 Mar 11 23:52 |
| Thanks, it looks much better in normal size, on the plane. I will hook it up with piping later today. |
| frwyflyer, Comment for image # 21540 | 08 Mar 11 21:42 |
| VERY NICE!! |
| John M Oshust, Image # 21540 | 08 Mar 11 18:55 |
Only one small step towards completion today.....The FUEL PUMP! |
| John M Oshust, Image # 21520 | 07 Mar 11 19:26 |
The Pfalz D-IIIa, my next attempt at building a bit of history. |
| John M Oshust, Comment for image # 21513 | 07 Mar 11 17:52 |
| Moos you must be psychic. Kay, at aerodrome RC, cut my next build this past Saturday. It arrived today. VA has enough Fokkers, but I do not recall seeing a Pfalz D-IIIa!!! |
| moostang51, Comment for image # 21513 | 07 Mar 11 17:46 |
| Hey, you could always do a Fokker DR-1. Nice. |
| John M Oshust, Image # 21516 | 07 Mar 11 17:44 |
All lower support cables and control wires are in order. |
| John M Oshust, Image # 21513 | 07 Mar 11 17:43 |
Just when I started to get the nack of this, the wiring of the feathers is over! |
| John M Oshust, Image # 21511 | 07 Mar 11 17:42 |
|
| John M Oshust, Image # 21510 | 07 Mar 11 17:42 |
With the aroma of 5 min. epoxy floating about, the top air foil is added. |
| John M Oshust, Image # 21509 | 07 Mar 11 17:40 |
Awaiting the epoxy molecular magic. The upper air foil shall be permanent. |
| poppy, Comment for image # 21484 | 06 Mar 11 21:38 |
| WOW! |
| JohnG., Comment for image # 21484 | 06 Mar 11 17:25 |
| Intricate work beautifully executed. This sort of thing can sure cross the eyeballs. |
| John M Oshust, Image # 21484 | 06 Mar 11 16:21 |
The feathers thru the wings. |
| John M Oshust, Image # 21483 | 06 Mar 11 16:11 |
Started the slow tand tedious rigging process. |
| John M Oshust, Image # 21482 | 06 Mar 11 16:10 |
I have the chart listing original wire specs. I tried to vary the material to replicate the original. Plastic coated beading wire was used for the elevator control lines. I is a braided cable like the original. |
| John M Oshust, Image # 21481 | 06 Mar 11 16:08 |
Spent most of the afterenoon and only totally finished the right side |
| John M Oshust, Image # 21480 | 06 Mar 11 16:06 |
Me thinks they can be seen here. |
| Build Thread, Page :
1 2 3 4 5 6 7 8 9 10 11 >> (423 posts, 20 posts per page, 22 pages in total)
|
[ < Prev ] [ Next > ] |
